Register FAQ Members List Calendar Mark Forums Read
Old 05-04-2010, 09:56 AM
SpicemasterBob's Avatar
SpicemasterBob SpicemasterBob is offline
Slow Smoker
Join Date: Nov 2009
Location: Corpus Christi, Texas
Posts: 107
SpicemasterBob is on a distinguished road

Default Offset Firebox Design ???

Did a little research and couldn't find an answer that fit my question, so I thought some of y'all could help.

We're building an offset smoker that's made up of (2) 24" lengths of sch. 40 pipe. We are trying to determine what is the ideal size opening from the firebox to the smoker side. The smoker box will have just a single grate with tuning plates positioned approximately 3" below that surface. I understand that good airflow is critical to the design, but I'm a little confused as to the size of the opening into the smoker box and the ideal distance of the opening to the grate/tuning plate level.

Please help with your suggestions and/or opinions.
Reply With Quote
Old 05-04-2010, 04:13 PM
la coonass la coonass is offline
Join Date: Mar 2010
Posts: 17
la coonass is on a distinguished road

Question Pit building calculations

I'm a newbie and wanted to know size of firebox in relation to the cooking chamber and size opening from inlet to firebox and from firebox to cooking chamber. These guys on this forum are great and will all give a hand when they can. I found the pit building calculations on another forum, but I'm not sure if I can post that info on this forum, If someone would let me know how to get that info to you I would gladly do it. Can we post email addresses here is another question I have Thanks in advance
Reply With Quote
Old 05-04-2010, 05:54 PM
cappy cappy is offline
BBQ Guru
Join Date: Jan 2007
Posts: 1,202
cappy will become famous soon enoughcappy will become famous soon enough


Aperture size from firebox to smoking chamber:

On my pit (20x52" smoking chamber), the aperture is 15" wide by 5.5" tall, like a semi-circular piece of pie completely cut from the bottom side of the smoking chamber. There is a semi-circular baffle (essentially the part that was cut out), angled from the top edge and protruding into the smoking chamber to deflect heat and smoke initially to the bottom of the pit. See this picture:

You can also see an example of an angled baffle from the smoking chamber side in Simon's second picture in this thread:

As far as the location of the tuning plates is concerned, I don't have them, but on a 24" pit I would think they ought to be further away from the cooking grate than 3 inches.

See this thread:

And this one where PitBull experimented to find a way around his radiant heat problem coming from the plates:

As far as the question la coonass had about firebox size, 20x20 square or 24x24 are pretty common sizes. I have a 20"Wide x 24"Long square firebox on my 20x52" Klose which also has an upright on the end. That size firebox is more than sufficient for the pit. It had plenty of room around the fire.

See this thread for examples showing my fire size:
Reply With Quote
Old 05-05-2010, 12:07 PM
SpicemasterBob's Avatar
SpicemasterBob SpicemasterBob is offline
Slow Smoker
Join Date: Nov 2009
Location: Corpus Christi, Texas
Posts: 107
SpicemasterBob is on a distinguished road


Thanks Cappy!! A ton of great info, much appreciated!
Reply With Quote
Old 05-07-2010, 01:10 AM
SpicemasterBob's Avatar
SpicemasterBob SpicemasterBob is offline
Slow Smoker
Join Date: Nov 2009
Location: Corpus Christi, Texas
Posts: 107
SpicemasterBob is on a distinguished road


Our firebox runs the length of the pit as it is mounted parrallel to the main chamber. We can get get approximately a 6-7 hour 340 +/- degree burn in moderate temps and low wind conditions without ever opening the box. We light one end with a torch and strategically place mesquite sticks along the sides to smoke as required and use carbon or Kingsford when we are after just heat.

I agree that when you open the doors with more frequency the quality of your product suffers.

Thanks again for the input, please stop to say hello if we are ever at the same event. We are Piping Hot BBQ

Last edited by SpicemasterBob; 05-07-2010 at 11:40 AM..
Reply With Quote
Old 08-02-2010, 07:59 PM
Teddy N Texas's Avatar
Teddy N Texas Teddy N Texas is offline
BBQ Guru
Join Date: Apr 2007
Location: Sherman, Texas
Posts: 1,532
Teddy N Texas is on a distinguished road


Thanks Cappy for all the good info. I have never added wood with just a 10* drop in temp. That could be why I have to fight so hard to keep the temp up. I will try adding wood as you suggested the next time I cook.
Reply With Quote
Old 08-04-2010, 11:12 PM
WestCoastSmoke's Avatar
WestCoastSmoke WestCoastSmoke is offline
Join Date: Jul 2010
Location: Monterey, CA
Posts: 30
WestCoastSmoke is on a distinguished road


Try this site:
Reply With Quote
Old 08-05-2010, 05:16 PM
bigwheel's Avatar
bigwheel bigwheel is offline
BBQ Pitmaster
Join Date: Sep 2004
Location: Cowtown, TX
Posts: 5,982
bigwheel has a spectacular aura aboutbigwheel has a spectacular aura about


Well I would put the cook chamber on top of the firebox. That saves a bunch of steps and conforms closer to the laws of physics as concerns the old hot air rising deal. Should
make it a bunch mo fuel efficent than trying to force it to go sideways. Hot air do not like to act like that.

Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
New design gatorpit BBQ Pits 23 09-30-2009 08:01 AM
Firebox under. Not Offset. Better Design? iwnly BBQ Pits 1 08-20-2007 06:32 AM
Pit design Rookie BBQ Pits 15 01-14-2006 06:52 AM
Offset Firebox vs Rear Firebox Pits.. DarrelB BBQ Pits 19 12-21-2005 07:06 AM
Firebox Design kjt1010 BBQ Pits 8 03-30-2004 10:50 AM

All times are GMT -5. The time now is 06:29 PM.
Style Developed by Andrew Slane

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Contact Us - - Archive - Top